Flintshire · Wales
Lighting bollard installation in Mold
Lighting bollards for sites across Mold and the rest of Flintshire, from the first measurement to the last relaid paving block.
Computer-generated imageAbout lighting bollards in Mold
Outdoor lighting bollards need weatherproof and impact-resistant construction and must be connected and tested by a qualified electrician. In Mold, that tends to mean sites such as residential driveways, small industrial units and local parades.
We work across CH7 — Mold itself and places including Mynydd Isa, Northop Hall, Drury and Treuddyn. Nearby, we also work in Deeside (4.9 miles), Flint (5.4 miles), Coedpoeth (8.5 miles) and Wrexham (10.4 miles), measured as the crow flies.
Mold at a glance
- Area
- Flintshire, Wales
- Highway authority
- Flintshire County Council (local roads)
- Planning authority
- Flintshire County Council
- Postcodes
- CH7
- Guide price
- Typically £335–£1,145 per bollard + VAT (£395–£1,345 inc VAT for homes); minimum job £815
- Survey
- Free, with a fixed written quote
Guide prices for Mold
| Specification | Guide price | Includes |
|---|---|---|
| Standard | £335–£685 + VAT · £395–£815 inc VAT | Standard post, foundation, reinstatement |
| Upgraded | £585–£925 + VAT · £695–£1,095 inc VAT | Upgraded finish or fittings, reflective band, matched keys |
| Premium | £825–£1,145 + VAT · £985–£1,345 inc VAT | Heavy-duty or architectural spec, premium finish |
Per bollard, installed with a qualified electrician (supply run extra); -3% for Wales. Guide only — the fixed price follows a survey.
Typical lighting bollards jobs in Mold
Typical reasons Mold sites choose lighting bollards:
- Parks and areas where tall columns would be intrusive
- Private gardens and long driveways
- Footpaths through housing developments and campuses
What we check first in Mold
Before digging near the kerb in Mold we establish who owns the ground: adopted footways are Flintshire County Council's responsibility, trunk roads the Welsh Government's, and everything else belongs to the site owner.
Many private-land installations in Mold need no planning application, but the rules don't clearly cover bollards, so listed buildings, conservation areas and prominent frontages are worth raising with the planning team at Flintshire County Council before posts go in.
Cable trenches run between every position and back to the supply, often crossing paths, drives and planting, so the routes are planned to minimise cuts through hard surfaces and to avoid existing gas, water and telecoms services. Bases are set in firm ground with the cable entry facing the right way, and on paved routes the bollards are positioned so cables can be pulled through ducts rather than requiring surfaces to be lifted again later.
- Limit glare and upward light, and check for any planning or ecology conditions on lighting near sensitive habitats.
- Choose IP and IK ratings that suit the location, and do not rely on lighting bollards as vehicle barriers.
What happens on site
Dig cable routes
Trenches are dug between bollard positions and the supply point, avoiding existing services, with cable or duct laid at a suitable depth and warning tape above.
Test, aim and certify
The circuit is tested and certified, bollards are checked at night for coverage and glare, and asymmetric heads are turned to face the path.
Reinstate
Trenches are backfilled and surfaces made good, whether paving, tarmac, gravel or turf.
Options to consider
| Option | Detail |
|---|---|
| Solar bollards | Self-contained with panel and battery; no cabling. Suited to markers and low-use routes where lower output is acceptable. |
| Controls | Photocells, timers, motion sensors and dimming to light only when and as much as needed. |
| Light distribution | 360-degree, asymmetric or louvred heads to light paths while limiting glare and light spill. |
What moves the price in Mold
Our Wales guide prices are a starting point; the survey in Mold firms them up. What tends to move them:
- Controls such as photocells, timers or sensors
- Length of cable routes and surfaces to be cut
- Mains or solar bollards
Looking after them
LED lighting bollards need far less maintenance than older lamp types, but they are not maintenance-free. Clean diffusers so dirt and algae do not dim the light, check seals and fixings, and look for impact damage, especially in car parks.
For damaged or loose posts in Mold, repairs and replacements are priced in writing first.
Questions about lighting bollards in Mold
Do you install lighting bollards in Mold?
We cover all of Mold (CH7) and the rest of Flintshire. We also work in Deeside, Flint and Coedpoeth.
Do I need consent for lighting bollards on a public footway in Mold?
In Mold the highway authority for local roads is Flintshire County Council. We confirm whether the ground is adopted highway before quoting, because lighting bollards on a public footway need its agreement first.
How much do lighting bollards cost in Mold?
In Mold, typically £335–£1,145 per bollard, installed with a qualified electrician (supply run extra), plus VAT (£395–£1,345 including VAT for homeowners), with a minimum job of £815 plus VAT, using our Wales guide prices. The fixed figure comes in writing after we've seen the site.
Will lighting bollards survive in a car park?
Choose robust bodies with a high impact rating and place them where vehicles are unlikely to hit them, such as behind kerbs or alongside protective posts. A lighting bollard is not designed to stop a car.
Can bollard lights work on a timer or motion sensor?
Yes. Photocells switch them on at dusk, timers switch them off or dim them late at night and motion sensors bring them up when someone approaches. Combining controls saves energy and reduces light pollution.